We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Mechanics of machines Lab report

essay
The whole doc is available only for registered users

A limited time offer! Get a custom sample essay written according to your requirements urgent 3h delivery guaranteed

Order Now

Introduction
The motion of assemblies is determined by the configuration of links and joints. Using the configurations the operation of rotational and sliding joints are examined and observed. This kind of mechanism is very commonplace in machines. Machines are made up of a number of parts and relative motion between the various parts permits the working of the machine. As the crank is rotated the rod starts moving but the velocity is not uniform. It is greater towards one direction than the other. This principle is utilized extensively in some machines.

Aim
Understand the relative motion of the rotational and sliding joint. Understand the movement of the rotational and sliding joint and graph the peculiar behaviour. To investigate the reason for such movement.

Procedure
The assembly is set up such that one end of the rod moves up and down when the crank (to which the other end of the rod is attached) is rotated. So, now the movement depends on the rotation of the crank. It is made sure that there is space for the rod to move on the complete rotation of the crank. Once the setup is done, readings are taken for every 10 degrees movement in the crank. Once done, the appropriate readings are marked on the graph. Using this graph another graph for velocity with time and acceleration with time are made. Looking at the velocity graph helps find out if the movement of the slider is faster than the other.

Result
It is observed that the movement of the slider is faster towards one direction than the other while the crank is rotated. This is because the rotation for one direction is shorter than the other. This principle is widely used in various machines. One commonly used function is called the quick return mechanism. In this the faster stroke is used to do the work whereas the slower stroke is used to get it back to its position.

Calculation and Discussion
The data is obtained upon performing the experiment.

On observing the results it can be seen that the connecting rod initially moves forward then moves back and then again moves forward during the cranks entire rotation of 360 degree. If the configuration is changed different results are obtained. A graph can be plotted based on the above data as follows.

Graph of The movement of slider and the angle of rotation. If we assume that it takes 2 sec for the crank to complete one full rotation then another graph can be plotted with time on the X axis and the movement of the slider on the Y axis. This graph shows the time dependent movement of the slider.

Graph of the movement of slider with respect to Time. This graph is used to derive determine the velocity of the slider. The derivative of the movement of the slider with respect to time ie- ΔX/Δt gives the velocity of the slider when the crank is rotated.

Graph of velocity for the slider. It can be seen that initially the velocity is high and then as the crank is rotated the velocity falls getting to zero and then continues in the negative direction until it starts increasing again. The acceleration of the movement of slider is again found by differentiating velocity with respect to time.

Graph of acceleration for the slider. It is observed that the slider moves faster towards the return stroke compared to the forward stroke. This is observed when the crank is rotated in an anti clockwise manner and the results vary when the rotation is clockwise.

Conclusion
From the performed experiment it is observed that the slider moves when the crank is rotated. Depending upon the configuration of the mechanism and the rotation of the slider, it shows peculiar movement. In this case the slider moved faster towards the return stroke than the forward stroke. This conclusion is exploited in various machines and is termed as quick return mechanism. This is due to the shorter angle of movement for the slider to move one direction than the other.

Related Topics

We can write a custom essay

According to Your Specific Requirements

Order an essay
icon
300+
Materials Daily
icon
100,000+ Subjects
2000+ Topics
icon
Free Plagiarism
Checker
icon
All Materials
are Cataloged Well

Sorry, but copying text is forbidden on this website. If you need this or any other sample, we can send it to you via email.

By clicking "SEND", you agree to our terms of service and privacy policy. We'll occasionally send you account related and promo emails.
Sorry, but only registered users have full access

How about getting this access
immediately?

Your Answer Is Very Helpful For Us
Thank You A Lot!

logo

Emma Taylor

online

Hi there!
Would you like to get such a paper?
How about getting a customized one?

Can't find What you were Looking for?

Get access to our huge, continuously updated knowledge base

The next update will be in:
14 : 59 : 59