We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Banana Oil Lab Report Essay Sample

essay
The whole doc is available only for registered users OPEN DOC

A limited time offer!

Get a custom sample essay written according to your requirements urgent 3h delivery guaranteed

Order Now

Banana Oil Lab Report Essay Sample

Introduction
In the banana oil lab we began with isopentyl alcohol + acetic acid  isopentyl acetate + Water. We needed for this experiment a hot plate, clamps, pipette, 5mL vial, caps, hoses and a thermometer. Upon starting, our group set up an open system experiment that allowed gases to be released to avoid pressure build up. We mixed together to molecules, 1.0mL of isopentyl alcohol, 1.5mL of acetic acid and added three drops of sulphuric acid. The acetic acid was used as a catalyst to speed up the reaction. Once all the needed chemicals were added we waited for about 70-75mintues for the reaction to take place. The desired temperature for the reaction was 150oC. We also had the solution at a constant stir.

After the reaction was done taking place, we began to purification process. We used a pipette to remove the excess water and impurities that were underneath the banana oil. We removed all that was available and then began to add sodium carbonate to help wash and dry the mixture. Slowly shaking the banana oil inside the 5mL side to side, allowing CO2 to escape the 5mL vial. We did this twice making sure all the excess impurities were removed. As we had our final solution of banana oil, we used the I.R. spectra to conclude our results. The I.R. spectra showed us that the compound we produced had no peak at 3300cm-1. The banana oil peaked at roughly 1750cm-1. We concluded from these results that all the alcohol was extracted and the final product was banana oil. Purpose

The purpose of our lab was to reflux an isopentyl alcohol with carboxylic acid (acetic acid), adding three drops of sulphuric acid acting as a catalyst to produce an ester (isopentyl acetate) and water. We verified our answers using infrared spectroscopy.

Calculations for Percent Yield
To find the percent yield we had to first find moles of our limiting reagent.
1) Weight of 5mL vial + cap =28.2526g
2) Weight of 5mL vial + cap +1.0mL of isopentyl alcohol= 28.9852g
3) Weight of 5mL vial + cap + 1.0mL of isopentyl alcohol + 1.5mL acetic acid= 30.5185g

First we calculated the difference of the 1 and 2 (2-1= difference)= 0.7326g. Then, we found the difference of 1 and 3, =1.5333g. Using the molecular weight of the molecules of isopentyl alcohol and acetic acid we found the moles of each molecule. For isopentyl alcohol we calculated, (0.7326g/1) / (88.2g/mol=).0083 moles of isopentyl alcohol. The moles for acetic acid were calculated at 0.0255 mol= (1.5333g/1) / (60.1g/mol). Once we found that isopentyl alcohol was the limiting reagent, we found how many grams of banana oil were possible to produce. This number came out to be, (0,0083mol) x (130.2g/mol)= 1.08066g= theoretical yield. Our final product (actual yield) we produce 0.4127g of banana oil. We then took this number to find our percent yield, (0.4127g)/(1.08066g) x 100= 38.2%

Purification Process
For the purification process we needed to rid the solution of any excess chemicals besides the banana oil. To do this, we needed to understand a little about what makes a solution. Two factors that affect the ability of a solution to form are: 1) the natural tendency of substances to mix and spread into larger volumes when not restrained in some way 2) the types of intermolecular forces in the solution.

In the case of the alcohol and the carboxyl acid, the two molecules reacted to form isopentyl acetate and water. All of the isopentyl alcohol was reacted with acetic acid and due to the solubility between the two molecules we were able to extract the water and acetic acid. This was done using a pipette to remove the bottom layer of the solution and it was possible because the alcohol was not soluble in the water. The second extraction required the use of one mL of sodium carbonate to wash the mixture by slowly shaking it until the bubbling stopped. We then removed the cap to allow the release of carbon dioxide out of the mixture, this was done two times. Finally, we began drying the mixture with sodium sulfate.

Results from Infrared Spectroscopy
After completing the washing a drying of our mixture, we then took our final product to be tested using infrared spectroscopy. Only items needed for this was the I.R. spectra, a pipette, and a computer. We placed a drop on the eye of the spectrograph and waiting for our results. We noticed from our finding that at 3300cm-1 our mixture had no peak. This meant that we successfully removed all the excess alcohol from our mixture. Furthermore, we notice a distinct peak at 1750 cm-1. This confirmed that we in fact had banana oil as our final product.

Conclusion
In this experiment we ended up with a percent yield of 38.2%. The reasons for a lower percent yield could be attributed to factor not all isopentyl alcohol reacting and extracting some of the product out with the excess water.

The isopentyl alcohol is a hydrophobic molecule with a hydrophilic head end. This allows the molecule to react with the carboxylic acid which is a hydrophilic molecule. We know this by the bonds associated with both molecules. The alcohol is a non polar

By using the I.R. spectra, we first noticed that there was no peak at 3300cm-1. This is significant because if there was any excess alcohol within the mixture we would see a peak. At 1739.31cm-1, we see a noticeable peak showing us that for our final product we did in fact have banana oil.

We can write a custom essay

According to Your Specific Requirements

Order an essay
Get Access To The Full Essay
icon
300+
Materials Daily
icon
100,000+ Subjects
2000+ Topics
icon
Free Plagiarism
Checker
icon
All Materials
are Cataloged Well

Sorry, but copying text is forbidden on this website. If you need this or any other sample, we can send it to you via email.

By clicking "SEND", you agree to our terms of service and privacy policy. We'll occasionally send you account related and promo emails.
Sorry, but only registered users have full access

How about getting this access
immediately?

Become a member

Your Answer Is Very Helpful For Us
Thank You A Lot!

logo

Emma Taylor

online

Hi there!
Would you like to get such a paper?
How about getting a customized one?

Can't find What you were Looking for?

Get access to our huge, continuously updated knowledge base

The next update will be in:
14 : 59 : 59
Become a Member