Complexometric Determination of Nickel using EDTA Essay Sample

Complexometric Determination of Nickel using EDTA Pages
Pages: Word count: Rewriting Possibility: % ()

The Aim of the experiment is to determine the percentage of nickel salt using a complexometric technique. Ethylenediaminetetraacetic acid (EDTA) is a hexadentate ligand which forms stable complexes with most metal ions, thus is widely used to determine metals in complexometric titrations. EDTA can be represented as H4Y and in alkaline conditions, it exists as Y+ ions:

The Y4- ions form 1:1 complexes with metal ions. For example, Ni2+ ions bind with them to form a stable octahedral complex NiY2-. An ordinary indicator cannot be used since the reaction does not involve a simple acid – alkali neutralisation so the end point of an EDTA complexometric titration can be detected by means of a metal ion indicator (an organic dye which changes colour when it binds with metal ions.) For it to be suitable in an EDTA titration, the indicator must bind less strongly with the metal ions than does EDTA. Procedure:

Firstly, the theoretical percentage by mass of nickel in NiSO46H20 was calculated. Approximately 2.6g of hydrated nickel(II) sulphate was transferred to a weighing bottle and both the contents and bottle were weighed. About 25cm3 of deionised water was added to a 100cm3 beaker and the bulk of the nickel salt was transferred to the water. The weighing bottle was then reweighed with the remaining salt. The solution in the bottle was stirred until the solid dissolved and the solution was then transferred to a 100cm3 standard flask. The beaker was then rinsed with deionised water and the rinsings were added to the standard flask. This procedure was repeated until the solution reached within a centimetre of the graduation mark on the standard flask. Using a dropper, the solution was made up to the graduation mark with deionised water. The flask was stoppered and inverted several times to ensure the contents were thoroughly mixed.

The burette was then rinsed with 0.10mol l-1 EDTA and filled with the same solution. The pipette was rinsed with a little of the nickel salt solution and 20cm3 of this was pipetted into a conical flask. The solution was then diluted to about 100cm3 with deionised water. Approximately 0.05g of murexide indicator was added to the diluted nickel salt solution together with approximately 10cm3 of ammonium chloride solution. The mixture was then titrated with the EDTA solution and after the addition of about 15cm3 EDTA solution, the solution was made alkaline by the addition of approximately 10cm3 of 0.88 aqueous ammonia.

The titration was then continued to the end-point which was shown by the first appearance of a blue-violet colour. This titration was used as a trial run, as detection of the end point is very difficult. The titrated solution was kept to help detect the end-points in the subsequent titrations. The titration was repeated until two concordant results were obtained. The percentage by mass of nickel in the sample of hydrated nickel(II) sulphate was calculated using the accurate concentration of the EDTA solution. For one determination, the percentage error was calculated and then the absolute error in the percentage of nickel in NiSO4 6H2O.

Theoretical Calculation:
GFM of hydrated nickel(II) sulphate, NiSO4.6H2O = 262.8
X 100 = 22.3%
%Ni = 58.7

Experimental Results:
Mass of hydrated nickel(II) sulphate used = 2.6g
| Rough titre| First titre| Second titre|
Initial burette reading (cm3)| 0| 19.5| 0|
Final burette reading (cm3)| 19.5| 40.8| 21.5|
Volume of EDTA added (cm3)| 19.5| 21.3| 21.5|

Average of concordant results:
= 21.4 cm3
21.3 + 21.5
Concentration of EDTA solution = 0.10mol l-1

The number of moles of EDTA used to react with 20cm3 of nickel(II) solution =V x C
= 0.0214 x 0.10 = 0.00214 moles
Therefore, number of moles of Ni2+ ions in 20cm3
= 0.00214 moles
Number of Ni2+ ions in the total volume of 100cm3
=0.00214 x 5 = 0.0107 moles

Therefore, mass of nickel in salt
= N x Fm
= 0.0107 x 58.7
= 0.62809g
X 100
From these results the % mass of nickel in the salt

= 0.62809
= 24.2%

The percentage by mass of nickel in hydrated nickel(II) sulphate was shown by experiment to be 24.2%. This compares very well with the theoretical value of 22.3%.

The experimental result fits in very well with the theoretical result. This suggests that the hydrated nickel(II) sulphate used was very pure. Impurities such as other metal ions would have reacted with EDTA to give higher titre values and, therefore, a higher experimental value for the percentage of nickel present. During the first titration, it was quite difficult to determine when the end-point had been reached, but the appearance of the blue-violet colour was sharp. The ammonia-ammonium chloride solutions are used as a buffer to keep the pH constant. Possible uncertainty values in the measurements include:

* Burette readings ±0.05 cm3
* Pipette volumes ± 0.06 cm3
* Balance readings ± 0.01g (±0.02g for tared mass)
* Volumetric flasks ± 0.2 cm3
* The concentration of the EDTA solution.

Uncertainty Calculations:

Uncertainty in mass of NiSO4.6H2O
= 0.02g
X 100 = 0.77%
% uncertainty in mass of NiSO4.6H2O
= 0.02

Uncertainty in volume of NiSO4 (aq)
= 0.2cm3
X 100 = 0.20%
% uncertainty in volume of NiSO4 (aq)
= 0.2

Uncertainty in pipetted volume of NiSO4 (aq)
= 0.06 cm3
X 100 = 0.3%
% uncertainty in pipetted volume of NiSO4 (aq)
= 0.06

Uncertainty in concentration of EDTA = 0.0002mol l-1
X 100 = 0.2%
% uncertainty in concentration of EDTA
= 0.0002

Uncertainty in titre volume of EDTA = 0.1cm3
X 100 = 0.5%
% uncertainty in titre volume of EDTA
= 0.1

% uncertainty in percentage of Ni
= 0.77 + 0.2 + 0.3 + 0.2 + 0.5
= 1.97%

X 24.2 = 0.48%
Absolute uncertainty in percentage of Ni
= 1.97

Hence, percentage of Ni in NiSO4.6H2O
= 24.2±0.5%

Search For The related topics

  • acid
  • Olivia from Bla Bla Writing

    Hi there, would you like to get such a paper? How about receiving a customized one? Check it out

    Haven't found the Essay You Want?
    For Only $13.90/page