We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Determination of the Amounts of Sodium Hydroxide Solution Essay Sample

essay
The whole doc is available only for registered users OPEN DOC
  • Pages:
  • Word count: 2228
  • Category: solutions

Get Full Essay

Get access to this section to get all help you need with your essay and educational issues.

Get Access

Determination of the Amounts of Sodium Hydroxide Solution Essay Sample

Introduction

Sodium carbonate and sodium hydroxide are both alkaline in nature. When hydrochloric acid is added to the mixture, sodium hydroxide reacts like this:

NaOH + HCl —–> NaCl + H2O ………………….. (1)

Sodium carbonate reacts with hydrochloric acid in a similar way but the reaction comes in 2 steps:

Na2CO3 + HCl ———–>NaHCO3 + NaCl…………. (2)

NaHCO3 + HCl ———–>NaCl + H2O + CO2………. (3)

The pH conditions in which reactions (1) and (2) take place are approximately the same: they both occur at a relatively higher pH (at a pH value higher than 7). Reaction (3) is quite different from the other 2 reactions. It takes place at a lower pH (at a pH value lower than 7).

So, using the 2 acid-base indicators, the end points for the reactions can be found. Phenolphthalein turns from pink to colorless as the pH value changes from 10 to 8. Methyl orange turns from yellow to orange when the pH value drops from about 4 to 3.

After adding phenolphthalein and then titrating the solution, the end point for reactions (1) and (2) can be found. If we further add methyl orange and titrate the mixture afterwards, the end point for reaction (3) is also found. By considering the amount of hydrochloric acid used for both titrations, the percentage by mass of sodium carbonate and sodium hydroxide can be found.

This is just one of the methods to determine the percentage by mass of sodium carbonate and sodium hydroxide. We can make use of barium chloride in this case. This is because when barium ions and carbonate ions come in contact, the following reaction occurs.

Ba2+ (aq) + CO32- (aq) ————->BaCO3 (s)

How can we utilize this special point of barium ions? We can use this to precipitate out the carbonate ions. Then what would be left in the mixture would be sodium hydroxide only. Then, using phenolphthalein as an indicator, we could find out the number of moles of sodium hydroxide in the solution.

Then one may ask,’ How do I find out the percentage by mass of sodium carbonate using the second method?’ We can do so by titrating the pure solution (no barium chloride added) using methyl orange indicator. The end point indicates the amount of hydrochloric acid used to neutralize both sodium carbonate and sodium hydroxide. The total number of moles of both sodium carbonate and sodium hydroxide can be found. By this way, we can find the percentage by mass of the both substances.

Procedure

1. All the apparatus involved were washed beforehand.

Method 1

2. With a pipette, 25cm3 of the solution mixture was transferred into a conical flask.

3. Appropriate amount of hydrochloric acid of was poured into a burette, and the initial reading was taken.

4. Using phenolphthalein as an indicator, the solution in the conical flask was titrated by the hydrochloric acid. The titration stopped when the color of the indicator changes from pink to colorless. The reading was taken.

5. Methyl orange was further added to the solution. Titrate the solution until the color changed from yellow to orange. The readings were taken.

6. The conical flask was washed and the burette was filled with hydrochloric acid.

7. Steps 2 to 6 were repeated for 4 more times.

Method 2

8. 25 cm3 of the solution mixture was transferred to the conical flask with a pipette.

9. Hydrochloric acid was added into the burette, with the initial readings taken.

10. Using methyl orange as indicator, the solution in the conical flask was titrated until the color changes from yellow to orange. The readings were taken.

11. The conical flask was washed with tap water and rinsed by distilled water.

12. Steps 8 to 11 were repeated for 2 more times.

13. 25 cm3 of the solution mixture was transferred to the conical flask with a pipette.

14. Barium chloride solution was poured into the conical flask until no more white solids were formed.

15. Hydrochloric acid was filled into the burette. The initial reading was taken.

16. Using phenolphthalein as indicator, the solution in the conical flask was titrated until the color changed from pink to colorless.

17. The final readings were taken.

18. Steps 13 to 17 were repeated for 2 more times.

Data and Calculation

Method 1

1

2

3

4

5

Initial reading

3.3 cm3

2.5 cm3

0.1 cm3

1.5 cm3

3.5 cm3

Reading when color changes from pink to colorless ( Volume of HCl used)

17.2 cm3

(13.9 cm3)

17.2 cm3 (14.7 cm3)

13.7 cm3 (13.6 cm3)

15.4 cm3 (13.9 cm3)

17.5 cm3

(14 cm3)

Reading when color changes from yellow to orange ( Volume of HCl used)

22.5 cm3

(5.3 cm3)

21.5 cm3 (4.3 cm3)

18.7 cm3

(5.0 cm3)

20.5 cm3

(5.1 cm3)

22.7 cm3

(5.2 cm3)

(The 1st and 2nd titration were rejected as the 1st was a trail and the 2nd was inconsistent with other results)

Average volume of HCl used to neutralize both NaOH and Na2CO3 into water and hydrogencarbonate ions: (13.6 + 13.9 + 14) /3 = 13.833 cm3

Number of moles of HCl in this step: 13.833/1000 X 0.09868= 1.3651 X10-3 mol

So, the number of OH- and CO32- adds up to 1.3651 X10-3 mol.

Average volume of HCl used to neutralize hydrogencarbonate ions =

(5.0 + 5.1 + 5.2) /3 = 5.1 cm3

Number of moles of HCl in this step: 5.1/1000 X 0.09868 = 5.033 X10-4 mol.

So, there are also 5.033 X 10-4 moles of Na2CO3 in the experiment.

Mass of Na2CO3 in the experiment:

5.033 X 10-4 X (23 X 2 + 12 + 16 X 3)= 0.5335g

Mass of NaOH in the experiment:

(1.3651 X10-3 – 5.033 X 10-4) X (23 + 17)= 0.03442g

So, the percentages by mass of NaOH and Na2CO3 are 39.15% and 60.85% respectively.

Method 2

A table showing the volume of HCl used for reacting both Na2CO3 and NaOH

1

2

3

Final reading

22.6 cm3

40.8 cm3

19.7 cm3

Initial reading

3.1 cm3

21.6 cm3

0.5 cm3

Volume of HCl used

19.5 cm3

19.2 cm3

19.2 cm3

(Due to time limitations, only 3 titrations could be done and the first titration is not rejected)

Average volumes of HCl used = (19.5 + 19.2 X 2)/ 3 = 19.3 cm3

No of moles of HCl used = 19.3/1000 X 0.09868 = 1.905 X 10-3 moles

A table showing the volume of HCl used for reacting NaOH.

1

2

3

Final reading

27.7 cm3

35.5 cm3

43.6 cm3

Initial reading

19.7 cm3

27.7 cm3

35.5 cm3

Volume of HCl used

8 cm3

7.8 cm3

8.1 cm3

(Due to time limitations, only 3 titrations could be done and the first titration is not rejected)

Average volumes of HCl used = (8 + 7.8 + 8.1)/3 = 7.967 cm3

No of moles of NaOH in the titration = 7.967/1000 X 0.09868 = 7.862 X10-4 mol

No. of moles of HCL used to titrate Na2CO3 =

1.905 X 10-3 – 7.862 X 10-4= 1.12X10-3 mol

So, the no. of mole of Na2CO3= 1.12X10-3/2= 5.6 X 10-4 mol.

Mass of NaOH = 7.862 X10-4 X (23 + 17) = 0.03145g

Mass of Na2CO3= 5.6 X 10-4 X (46 + 12 + 16X3) = 0.0593 g

So, the percentages by mass of NaOH and Na2CO3 are 34.7% and 65.3% respectively.

Conclusion

In method 1, the percentages by mass of NaOH and Na2CO3 are 39.15% and 60.85% respectively.

In method 2, the percentages by mass of NaOH and Na2CO3 are 34.7% and 65.3% respectively.

Discussion

The results obtained from both experiments were not quite consistent. The reasons are to be discussed below.

Firstly, many human errors have occurred in the titration. For example, while shaking the solution inside the conical flask, I accidentally spilt a drop onto the table. A smaller amount of HCl would be required to reach the end point in this case. This is because a smaller amount of substance is actually being titrated.

Also, unlike the first titration, this experiment involves more end points to be determined. In the first TAS, the end point only needs to be determined once every titration. But this time, two determinations need to be made for every titration in the first method. If there are no definitions of ‘orange’ or ‘colorless’, which is actually the case, inconsistency and thus error will occur.

Furthermore, this is my first time using phenolphthalein to do titrations since the start of F.6. I forgot the fact that after the end point is reached, which is colorless, further adding HCl into the conical flask will not change the color of the solution. The solution will remain colorless. Errors will occur in this case. I may take the final readings , which an excess of HCl is added, and the readings would be wrong. The readings would be higher than the actual amount of HCl required to reach the end point.

So, due to above reasons, many errors were made in this experiment. Then how may I improve my experiment?

I figured out that the main reason for me to make so many errors was due to my poor time management. While others were already starting method 2, I was still working hard on method 1. I have used an unreasonably long time to wash the apparatus and my motion was too slow. If I could allocate my time appropriately, I would not have made so many errors.

Another way to improve is to use a pH meter instead of using an indicator to determine the equivalence point. The equivalence point would be determined more accurately using pH meter.

How do I know when to stop adding BaCl2 in method 2? My method is simple: add BaCl2 until no more white solid forms. I tilted the conical flask, and then I added BaCl2 using a dropper, dropping the Barium solution onto the side of the flask. If no white solid is formed, then I had finished adding BaCl2.

Answer To Study Questions

1. Explain the changes of colors of the indicators in the above titrations.

In method 1, the solution in the conical flask consists of NaOH and Na2CO3, which are basic. So, when phenolphthalein is added to the solution, the solution turns pink. The pH of the solution drops when HCl is added to the conical flask and the end point is reached. So, phenolphthalein eventually turns colorless.

In the second step of this method, methyl orange is added. As the solution in the conical flask is still alkaline, methyl orange is yellow at the beginning. When HCl is added to the conical flask and the end point is reached, the pH drops and the indicator turns from yellow to orange.

In method 2, there are two titrations. In the one without BaCl2 added, methyl orange was added initially. As the solution in the conical flask was alkaline, methyl orange turned yellow at the start. When HCl was added and the end point was reached, the solution become acidic and the indicator turned orange in color.

In the titration with BaCl2 added into the conical flask, phenolphthalein was added. Initially, the solution in the flask was alkaline. So, the indicator was pink at the start. After the end point was reached by adding HCl into the flask, the solution had a lower pH and the indicator turned to colorless.

2. Explain why the titration should be carried out slowly and with constant stirring in (b).

This can make sure that all sodium hydroxide have reacted before further adding hydrochloric acid into the conical flask. After adding barium chloride was added into the conical flask, precipitates were formed. These precipitates would hinder the reaction of sodium hydroxide and hydrochloric acid. So, in order to allow all the hydrochloric acid to be reacted before anymore of it is added, we need to stir it and do it slowly.

3. Suggest with reasons which method is more accurate in the experiment.

I think that method 2 is more accurate. This is because method 1 involves 2 end points in 1 titration. If an error was made in the first part of the titration in method 1, the results obtained in the second part would also be wrong.

Also, CO32- reacts in 2 steps. But how will I be able to confirm that some HCO32- has not further reacted to form carbon dioxide and water in the first part? This also lowers the accuracy of method 1.

We can write a custom essay

According to Your Specific Requirements

Order an essay

You May Also Find These Documents Helpful

Ammonium hydroxide solution

In the strong acid-weak base titration, 0. 1 M ammonium hydroxide ( NH4OH ) was titrated with 0. 1 M hydrochloric acid ( HCl ). 2-3 drops of phenolphthalein were added as indicator into the conical flask which contains 25mL of hydrochloric acid. Ammonium hydroxide was then titrated slowly into the conical flask and the conical flask was swirled gently to ensure the reaction is...

The concentration of nitrate ion in a...

Chemically modi? ed polymeric adsorbents are resins with functional groups such as phenolic hydroxyl, acetyl, sulfonic group or amino group, grafted on hyper cross linked polymers (Alexandratos & Natesan 1999), (Cai et al. 2005). Among these, aminated hyper cross linked polymers display a unique advantage in adsorption of aromatic sulphonates (Pan et al. 2005) phenol derivatives (Pan, Zhang, Wei & Ren 2008), and phenolic acids...

Using Hess's Law to Calculate Enthalpy Change

Controlled variables: - Mass of water - Mass of magnesium sulphate anhydrous - Mass of MgSO4.7H20 Materials: 1) Safety spectacles 2) 2 filter papers 3) Spatula 4) Digital balance 5) 2 polystyrene cups 6) Thermometer 7) Magnesium sulphate anhydrous 8) Magnesium sulphate-7- water 9) Distilled water 10) Measuring cylinder Procedure: Part A 1) Weigh 3.01g of MgSO4 anhydrous to the nearest 0.01g on a filter...

Investigating Macromolecules and their Properties

Introduction: Background: There are many nutrients that are present in an organism that provides it energy in order to grow and reproduce. Some nutrients are required in larger amounts compared to others. These nutrients, that are required in larger amounts, are known as macromolecules. Identifying and distinguishing these macromolecules can be beneficial to scientists. Knowing these macromolecules and how they are shaped can help scientists...

Quantitative Determination of Food Colouring in Jelly...

Introduction Food colouring are mainly used in the food processing industry today as colour gives the food product certain flavours as people associate colours with certain flavours. Some is to stimulate a colour that is perceived by the consumer as natural food products. Food colouring also provides an identity to foods, to mask natural variations in colour, decorative or artistic purposes or to protect flavours...

Get Access To The Full Essay
icon
300+
Materials Daily
icon
100,000+ Subjects
2000+ Topics
icon
Free Plagiarism
Checker
icon
All Materials
are Cataloged Well

Sorry, but copying text is forbidden on this website. If you need this or any other sample, we can send it to you via email.

By clicking "SEND", you agree to our terms of service and privacy policy. We'll occasionally send you account related and promo emails.
Sorry, but only registered users have full access

How about getting this access
immediately?

Become a member

Your Answer Is Very Helpful For Us
Thank You A Lot!

logo

Emma Taylor

online

Hi there!
Would you like to get such a paper?
How about getting a customized one?

Couldn't Find What You Looking For?

Get access to our huge knowledge base which is continuously updated

Next Update Will Be About:
14 : 59 : 59
Become a Member