We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Investigating the Damping of Motion in a Simple Pendulum through Induced Eddy Currents Essay Sample

essay
  • Pages: 5
  • Word count: 1,173
  • Rewriting Possibility: 99% (excellent)
  • Category: experiment

Get Full Essay

Get access to this section to get all help you need with your essay and educational issues.

Get Access

Introduction of TOPIC

Aim:

The aim of my experiment is to determine the different permeances of several metals by measuring the effects of eddy current damping of the motion of a simple pendulum.

Apparatus:

The experiment involved the use of the following equipment:

Electromagnet

Power Supply

Retort Stand w/ Boss & Clamp

3 rectangular pieces of metal, of equal volume. One of Aluminium, Copper, Titanium and Steel.

A Pendulum Arm

An Axle

Two Small Axle Clamps, to hold the Pendulum Arm in place

High Frame Rate Camera

Method:

To determine the effects of the induced eddy currents, I will measure the time taken for the pendulum to halve its maximum angle of deflection. I decided to use a starting angle of 30 degrees, large enough so as to minimise systematic error, but small enough that repeating the experiment wouldn’t take excessively long. By connecting a video camera to a computer, I will manually raise the pendulum until the arm is in line with a line marked at 30 degrees from the vertical. I will start recording, and then release the pendulum. Using frame by frame analysis of the video I will determine the frame when the pendulum was released, and the first swing in which the pendulum achieves strictly less than 15 degrees of deflection. By working out the number of frames this takes, and dividing by the frame rate of the camera, I can calculate the time taken. The equipment will be set up as in the diagram on the next page, although the camera is not shown in the diagram. I was careful to ensure that the pendulum’s swing was perpendicular to that of the magnetic flux between to the two sides of the electromagnet, so as to maximise the flux linkage.

Background:

When a conducting material passes through a magnetic field, it experiences what are known as eddy currents. The relative motion of the conductor to the magnetic field causes a circulating flow of electrons inside the conductor. These ‘eddy currents’ create electromagnets. According to Lenz’s law the induced current produced in a conductor will always flow in such a way that the produced magnetic field opposes

the field which produced it. An increase in magnetic field strength, or an increase in conductivity

Sorry, but full essay samples are available only for registered users

Choose a Membership Plan
of the material, results in an increase in eddy currents.

Risk Assessment:

Electrocution:

Likelihood = 1(Low)

Danger = 3 (Mild electrocution)

Risk Factor = 3×1 = 3 (Acceptable)

Dropping heavy equipment:

Likelihood = 1 (Low)

Danger = 3 (Possible fracture of toes, etc.)

Risk Factor = 3×1 = 3 (Acceptable)

Overall, the experiment is not a particularly dangerous one. There aren’t any very risky procedures, and hence the likelihood of all accidents is low. The currents and voltages being used may, at worst, cause pain and burns, but the chances of electrocution are very low. Although heavy equipment is being used (namely the electromagnet core), it is not being moved regularly and as such does not present a serious risk, nor a reasonable chance of injury.

Other than the single anomaly, highlighted in red, the results of this experiment were very consistent, with at most .6 of a second difference between any two repeats. Overall, this method has proven to give good results in terms of consistency. The main limitations in my experiment were the maximum frame rate of the camera, and the fact that not all frames were recorded, as some were ‘dropped’ during transmission from camera to computer. I made sure that I got the best results I could by setting the camera to it’s maximum frame rate of 30 frames per second.

The results are not what one would expect. My background research suggested that an increase in conductivity would result in an increase in the induced eddy currents. Hence, a decrease in resistance would have the same effect, with conductivity being equivalent to (1/resistance). Following are typical values for the resistance of the metals I tested, in ascending order:

Copper

16.78 nΩ·m

Aluminium

26.53 nΩ·m

Titanium

427 nΩ·m [1]

Austenitic Stainless Steel

690 nΩ·m

Thus one would expect Copper to be effected most by the induced eddy currents, when it was in fact quite the opposite. One possible explanation for this would be to do with the fact that the metals have very different densities. Because of the differences in densities between the metals, it was impossible to keep constant both the volume and the mass. Having opted to keep the volume the same, there was large variation between the masses of the metals. Looking now at a table comparing the densities of the materials (on the next page), we see the vast difference between the density of aluminium and that of the other metals. It seems that the large percentage decrease in aluminium was simply due to its lower mass, and therefore decreased momentum. In fact, the results seem to follow exactly the trend represented by the density – that is, the greater the density, the greater the momentum, and thus the less effective the eddy current dampening.

Copper

8960 kg/m3 [2]

Aluminium

2700 kg/m3

Titanium

4500 kg/m3

Austenitic Stainless Steel

8000 kg/m3

Conclusion

All in all, the experiment did not achieve its goal. Whilst the method did yield good results, the factors I was trying to measure were simply too small when compared to others over which I had little control.

I did not seek any help throughout the duration of my coursework.

References:

[1] Titanium By J. C. ( James Case) Williams, G. (Gerd) Lütjering, Lutjering, Springer, 1994

[2] http://www.simetric.co.uk/si_metals.htm

We can write a custom essay on

Investigating the Damping of Motion in a Simple Pe ...
According to Your Specific Requirements.

Order an essay

You May Also Find These Documents Helpful

Designing an Osmotic Potential Experiment with Potatoes

Osmosis is used throughout the kitchen in various countries. In France, aubergines and cucumbers are often soaked in salt to create a nicer texture, however chefs lack understanding of why this happens, as they would have forgotten about it after they finished school, they only know that it happens. Therefore, this experiment is designed to explain to the millions of chefs around the world why the water is “sucked” out of a vegetable when it is dipped into a salt or sugar solutions. I believe that having knowledge over the reason for something can open up new ways of thinking; this is why I think it is so important to explain the reason behind this phenomenon. Famous chefs are also known to be under time pressure; for example, every cooking show on TV includes some sort of time pressure scenario, weather it is a ticking clock or waiting customers. For...

Investigating the Effects of Salt on Seed...

PROBLEM/RESEARCH QUESTION In this investigation, we are researching and investigating whether the concentration/percentage of NaCl (salt) in water affects the germination rate of seeds and if so, which concentration germinates the most seeds. We will formulate our research by conducting an experiment in which we will observe the germination of seeds in various concentrations of salt water and evaluate the results gathered. In particular, we will measure the percentage of seeds germinated in one week and formulate our conclusions from there. HYPOTHESIS I hypothesise that the highest percentage of seeds will germinate in the petri dish that contains the lowest percentage of NaCl in water- 0.5% salt salinity and the percentage will decrease as the percentage of salt in the solution increases. I predict this because I know from prior knowledge that seeds need to be able to absorb H2O to germinate and salt prevents this. So if we increase...

Investigating the Effect of Sodium Fluoride on...

Graph Showing the effect different volumes of Sodium Fluoride has on the average rate of production of H+ ions as measured by the colour change of resazurine Comment on Graph: The graph depicts a positive trend, as the amount of Sodium Fluoride increases the average rate of H+ ions as measured by the colour change of resazurine also increases. This increase is consistent with each 5 mL increase of Sodium Fluoride resulting in an increase of one assigned numerical colour. This steady increase plateaus at 15mL with no further colour change. Conclusion and Evaluation Conclusion In our experiment we tested whether changing the amount of Sodium Fluoride effects the rate of respiration as measured by the colour change of resazurine. Our experiment indicates that there is a relationship between sodium fluoride and the rate of respiration. In our experiment the more sodium fluoride that was added the less colour change,...

Popular Essays

logo

Emma Taylor

online

Hi there!
Would you like to get such a paper?
How about getting a customized one?